159
The position of the condyles and functional results after
bilateral sagittal split osteotomy
D. Hirjak
∗
, M. Beno, I. Kupcova, G. Branislav
Department of Oral and Maxillofacial Surgery, University
Hospital, Bratislava, Slovakia
Background:
The goal of this retrospective study was to evalu-
ate the influence of manual condylar positioning technique and
bicortical fixation after bilateral sagittal split osteotomy (BSSO)
on postoperative condylar position and temporomandibular joint
(TMJ) function after setback and advancement of the mandible.
Methods:
The condylar position and joint function of 32 patients
(64 joints) who underwent BSSO (setback/advancement of the
mandible) at the Department of Oral and Maxillofacial Surgery,
University Hospital in Bratislava between 2010 and 2014 was
analysed on computed tomography (CT) scans in three dimen-
sions (axial, coronal, sagittal plane) preoperatively and 1 year
postoperatively. Evaluation of the joint function was focused on
measuring the extent of maximal range of motion, propulsion and
lateropulsions and sounds presence.
Results:
CT scans evaluation revealed minimal changes of condy-
lar position in all three dimensions. There were no significant
changes in TMJ function in one-year follow-up equally after
setback or advancement of the mandible. Manual condylar repo-
sitioning technique and bicortical fixation using positional screws
created stable occlusion results.
Conclusion:
Manual condylar positioning after bilateral sagit-
tal split osteotomy and bicortical fixation creates an unimpaired
condylar position, good postoperative TMJ function and stable
occlusion.
http://dx.doi.org/10.1016/j.ijom.2017.02.546Anterior open bite correction by Le Fort I osteotomies with
or without anterior segmentation: which is more stable?
I.N. Ismail
∗
, Y. Leung
International Islamic University Malaysia, Kuantan, Malaysia
Background:
Anterior open bite (AOB) is one of the indications
for anterior segmentation of Le Fort I osteotomies. The stability
of the segmentation in AOB cases has not been widely reported.
Objectives:
A retrospective cohort study was conducted to anal-
yse the relapse rate of AOB correction comparing Le Fort I
osteotomies with or without anterior segmentation, and to assess
the risk factors that might contribute to relapse.
Methods:
Lateral cephalograms at six different times were ana-
lysed. A total of 85 patients with AOB were recruited. 39 patients
had Le Fort I osteotomy without anterior segmentation and 46
patients had anterior segmentation.
Findings:
Le Fort I osteotomy with anterior segmentation had
significantly more AOB relapse when compared to those without
anterior segmentation at postoperative seven weeks (15.3% versus
0%,
P
= 0.012). During early postoperative period, factors that
contributed to AOB relapse in Le Fort I osteotomy with anterior
segmentation were AOB closure more than 4 mm, inferior posi-
tioning of the anterior segment more than 2 mm and the maxillary
occlusal plane rotated in clockwise direction by 2
◦
. In long-term,
AOB closure more than 4 mm was the only identifiable factor that
caused more AOB relapse when treated by Le Fort I osteotomy
with anterior segmentation.
Conclusion:
Le Fort I osteotomies without anterior segmentation
was more stable in the surgical correction of anterior open bite at
early and late postoperative period.
http://dx.doi.org/10.1016/j.ijom.2017.02.547Splintless surgery: do patient-specific computer-aided
design/computer-aided manufacturing osteosynthesis
improve the accuracy of Le Fort I osteotomies?
J. Jansma
∗
, J. Kraeima, R. Schepers
University of Groningen, University Medical Center Groningen,
Groningen, The Netherlands
Background:
Three-dimensional (3D) planning of orthognathic
surgery is widely applied, in particular for treatment of patients
with asymmetrical maxillofacial deformities. Good surgical out-
come depends on careful virtual planning and adequate translation
to the actual surgical intervention. Correct positioning of the max-
illa after Le Fort I osteotomy in the transverse and sagittal planes is
usually guided by an intermediate splint while the vertical dimen-
sion is generally measured using intraoral or extraoral reference
points. Mismatch between the planned and realised maxillary
position can be caused by condylar sag.
Objectives:
This study aimed to develop and evaluate a new
method for positioning the maxilla that is independent of condylar
sag.
Methods:
Patient-specific computer-aided design/computer-
aided manufacturing drilling guides and osteosynthesis plates
were produced for positioning and fixation of the maxilla in three
cases (mean age, 40 years; range, 21–60 years) as part of a bimax-
illary osteotomy. Virtual surgical planning in each case was based
on cone-beam computed tomography. To analyse the accuracy of
maxillary positioning after Le Fort I osteotomy, a surface match
with the postoperative imaging was made.
Findings:
The area of the upper dentition in the postoperative
analysis showed a mean deviation of 1.3 mm (standard deviation,
1.4 mm) from the preoperative plan.
Conclusion:
This method enables accurate placement of the max-
illa, independent of the condyles or mandible, without the need for
extra oral reference points. The promising outcome of this pilot
study has led to the start of a large randomised controlled trial
(
n
= 60) in which the study methods are systematically compared
with conventional 3D-based splint surgery.
http://dx.doi.org/10.1016/j.ijom.2017.02.548Time-course changes of the mandibular position after
mandibular setback surgery in surgery-first approach
depending on the increase of vertical dimension and amount
of mandibular setback
M.S. Kook
School of Dentistry, Chonnam National University, South Korea
Background:
In surgery-first surgical orthodontic treatment, tran-
sient malocclusion can occur both due to occlusal interferences
immediately after surgery and increase in vertical dimension (VD).
As occlusal settling by removal occlusal interferences during the




