194
can necessitate the use of emerging operative techniques for ade-
quate management.
Objective:
This case report describes the use of a composite
osteomyocutaneous serratus anterior and double rib free flap for
the reconstruction of a complicated mandibular deformity on a
background of extensive failed reconstructions where more stan-
dard techniques, such as fibula flaps, were not available.
Methods:
The two rows of ribs were used to create a neomandible
and the skin paddle was used to cover the neck defect once the
appropriate chin projection was restored. The muscle was used for
the lining of the floor-of-mouth.
Findings:
The primary problems for the patient, prior to this
surgery, arose as a result of the severe Andy Gump deformity
and the subsequent functional impediments: oral incompetence
and saliva leak, severely impeded speech, and inability to swal-
low appropriately. The grounds of using a double rib approach
were to recreate the neomandible in such a way as to create a rigid
dam effect with sufficient depth to hold saliva. The benefits of the
flap included adequate bone transfer for functional and aesthetic
repair, with appropriate soft tissue coverage of the floor-of-mouth
and base of tongue.
Conclusion:
The author notes that this is not the flap of choice for
mandibular reconstruction, but identifies this as a novel alternative
to a free fibula flap in similar situation.
http://dx.doi.org/10.1016/j.ijom.2017.02.662Cook-Swartz Doppler Probe for evaluation of perfusion of
microvascular flaps
P.J. Voss
∗
, E. Mici, M.A. Füßinger, M. Metzger,
G. Bittermann, R. Schmelzeisen
Medical Centre University of Freiburg, Germany
Background:
Microvascular reconstructions are clinical routine
in maxillofacial surgery. In the literature, transplants are revised in
4–16% cases, and loss rates are between 0 and 6%. While trans-
plant survival is primarily dependent on perfusion of the flaps’
vessels, different methods have been described to control flap-
perfusion. The implantable Cook-Swartz Doppler Probe consists
of a piezo-crystal that is attached to a silicone strap. This strap can
be easily placed on the transplant-vessel, the probe is connected
to a Doppler device via a simple wire.
Methods:
In a single centre observational study, the Cook-Swartz
Doppler Probe was implanted in 63 consecutive patients that
needed a microvascular reconstruction in the maxillofacial region.
Findings:
In 47 patients, a flap was placed after tumour resection,
13 patients had an osteoradionecrosis and 3 had other diseases.
17 radial forearm flaps, 11 latissimus dorsi flaps, 3 scapula flaps,
12 combined latissimus dorsi-scapula flaps, 9 fibula flaps, 10 deep
circumflex iliac artery (DCIA) and 1 anterolateral thigh (ALT) flap
were used. 59 probes were put on the artery, 6 on the vein. In 12
patients the position of the vessels were corrected during wound
closure. Seven salvage operations were conducted successfully;
one DCIA transplant was lost after the salvage operation. In a
patient with radial forearm flap the probe was damaged during the
operation and could not be used. Following, the transplant was
lost. A combined latissimus dorsi-scapula transplant necrotised
even though the Doppler signal was positive.
Conclusion:
The Doppler control of the vessel perfusion dur-
ing wound closure enables direct corrections. In the postoperative
setting, the probe facilitates early salvage surgeries. Wrong posi-
tive Doppler signals are possible. Further investigations in larger
collectives are suggested.
http://dx.doi.org/10.1016/j.ijom.2017.02.663Preventing early-staged graft bone resorption by
simultaneous innervation in iliac bone flap for mandibular
reconstruction
L. Wang
∗
, J.H. Wei, L.Q. Xu, C.P. Zhang
Shanghai Jiao Tong University, Shanghai, China
Background:
The postoperative spontaneous resorption of vas-
cularised bone grafts jeopardises dental-implant-based functional
rehabilitation of jaw bones. Our recent studies and studies by oth-
ers demonstrate the crucial role of innervation in bone regeneration
and turnover.
Objectives:
To propose a novel strategy of simultaneous innerva-
tion in iliac flaps, and to evaluate its capabilities to prevent bone
resorption of grafts in mandible reconstruction.
Methods:
Based on animal experiments on goats, we developed
a new technique for simultaneous innervation of vascularised
iliac flap in mandibular reconstruction, through neurorrhaphy
between ilioinguinal nerves, which innervates iliac bone, and
residual nerves. Patients with postoncologic continuity defects of
the mandible underwent segmental mandibular reconstruction (10
innervated flaps and 12 control flaps). Graft bone resorption was
analysed by computed tomography scans at 6 and 12 months post-
operatively and bone quality was evaluated for suitability of dental
implantation, with histological and histomorphometric analyses
for graft bone samples.
Findings:
At 12-month follow-up, graft bone density loss and
osteoclast activity in control group were dramatically higher than
innervated group. Bone quality evaluation indicated suitable con-
dition for dental implantation in all the innervated group but 41.7%
in control group. Histological analyses showed successful inner-
vation and active osteoblastic differentiation from bone marrow
mesenchymal stem cells in innervated group but not control group.
Conclusion:
Innervated iliac flaps may effectively prevent bone
resorption of grafts in mandible reconstruction which otherwise
jeopardising the success of dental implants. This new strategy
appears clinically valuable and provides insights into the homeo-
stasis of vascularised grafts for functional reconstruction.
http://dx.doi.org/10.1016/j.ijom.2017.02.664Nasal reconstruction: a brief history, current techniques and
advances
L. Watson
∗
, H. Mohamedbhai, S. Dubb, C. Uzoho,
D. Coombes
Queen Victoria Hospital NHS Trust, East Grinstead, West
Sussex, England
Background:
The current practice of nasal reconstruction rep-
resents centuries of pioneering global developments, from the
first recorded cheek flap in ancient India (700 BC) to novel tis-
sue engineering studies and the exploration of computer-aided
design/computer-aided manufacturing (CAD/CAM) technology
today.




