Table of Contents Table of Contents
Previous Page  355 / 398 Next Page
Information
Show Menu
Previous Page 355 / 398 Next Page
Page Background

350

At 16 weeks post-discectomy, the animals were killed and TMJ

were taken out en bloc. TMJ osteoarthritis was evaluated by car-

tilage histology. The experimental procedures and protocol were

approved by the University Ethical Committee.

Findings:

TMJ of mice fed the high-fat diet showed increased

osteoarthritis degeneration compared to mice fed the normal diet.

High-fat diet group significantly gained weight more than the

normal diet group. There were hyperglycosemia during feeding

period in the high-fat diet group. Articular cartilage degeneration

was seen in both groups. Articular cartilage thickness became

thinner in the high-fat diet group than in the normal diet group.

The high-fat diet group tended to exhibit prominent disturbance

of chondrocytes and reduction of Safranin-O staining.

Conclusion:

These results suggest that the obesity induced by

high-fat diet increases the severity of cartilage degeneration in the

TMJ osteoarthritis model.

http://dx.doi.org/10.1016/j.ijom.2017.02.1177

Comparative analysis of regenerative potential of dental

pulp and dental follicle derived stem cells cultured on

polycaprolactone scaffolds for bone tissue engineering

approaches

E.M. Ozcan

∗

, Y. Erbilgin, N. Zibandeh, T. Akkoc, S. Basa,

K. Goker

Department of Oral and Maxillofacial Surgery, Marmara

University, Istanbul, Turkey

Background and Objectives:

Effects of dental pulp (DPSC) and

dental follicle (DFSC) derived stem cells on bone regeneration

are in focus of maxillofacial tissue engineering due to elimination

of donor site morbidity and promising osteogenic profile. In this

study, we aimed to compare the osteogenic potential of DPSC

and DFSCs on nano mesh containing (nmPCL) and plain (PCL)

polycaprolactone scaffolds

in vitro

.

Methods:

DPSCs and DFSCs were osteogenically differentiated

on PCL and nmPCL scaffolds and four groups were examined

for cell proliferation and type I collagen formation rates after 2

weeks of culture. Following immunofluorescence labelling, Non-

parametric (Kruskal Wallis) and multiple comparison tests were

used to compare the four groups.

Findings:

Among all groups, mean cell counts on scaffolds ranged

from 30.8 to 82.6 cells/0.0915 mm

2

, and total collagen formation

ranged from 2.79% to 17.9%. DFSC and nmPCL complex showed

significantly higher cell counts (

P

< 0.01) and collagen formation

rates (

P

< 0.01) in comparison to other groups.

Conclusion:

DFSC/nmPCL group is found to show superior

properties on cell proliferation and bone matrix formation. This

complex is a promising tool for maxillofacial tissue engineering

applications.

http://dx.doi.org/10.1016/j.ijom.2017.02.1178

Evaluation of user impressions, micromorphological bone

surface properties and material attrition by three

generations of osteotomy methods

A. Rashad

∗

, H. Hanken, B. Beck-Broichsitter, C. Rendenbach,

R. Smeets, A. Gröbe, M. Heiland

Department of Oral and Maxillofacial Surgery, University

Medical Center Hamburg-Eppendorf, Hamburg, Germany

Background:

Ultrasonic-driven osteotomy is associated with a

safe processing method and has broadened the daily used arma-

mentarium of maxillofacial surgeons. As further development,

sonic-based osteotomy method was newly introduced.

Objectives:

To analyse user impressions micromorphological

bone changes and material attrition by sound-, ultrasound and

conventionally driven osteotomy.

Methods:

In fresh bovine ribs conventional – (Lindemann-drill

H254E, Brasseler GmbH and Co. KG, Lemgo, Germany), sound

– (saw SFS 101 Brasseler GmbH and Co. KG, Lemgo, Germany)

and ultrasound (saw OT7S-4, Piezosurgery, Mectron Medical

Technology, Carasco, Italy) guided osteotomies were performed

by novice (N) and expert (E) practitioners with different irrigation

volumes. Bone surfaces were analysed by (environmental) scan-

ning electron microscopy. Energy dispersive spectroscopy was

carried out to detect possible material attrition.

Findings:

Sonic systemwas significantly slowest with worst noise

impact subjectively (N: 2.9, E: 3.2) and objectively (92.9 dB; SD

7.1). However, both user groups improved significantly in a sec-

ond run (N: 7.9, E: 7.6). Bone structure was mostly preserved

after sonic and ultrasonic assisted preparation. By contrast, using

the conventional technique showed significant changes especially

with regard to the cancellous layer of the bone with incorporation

of abundant bone debris. None of the tested treatment procedures

resulted in relevant attrition of drill materials.

Conclusion:

The practitioners had a promising experience with

ultrasonic and specially the sonic system. In contrast to conven-

tional osteotomy, osseousmicromorphologywasmostly preserved

by sonic and the piezoelectric method. This could have a posi-

tive effect on bone healing and osseointegration and should be

investigated in future studies.

http://dx.doi.org/10.1016/j.ijom.2017.02.1179

Multi-criteria based evaluation of treatment design options

for large polymethylmethacrylate-based skull

reconstruction: finite element analysis study of six cases

A. Ridwan-Pramana

∗

, J. Wolff, T. Forouzanfar

Department of Oral and Maxillofacial Surgery/3D Innovationlab

VU University Medical Center, Amsterdam, The Netherlands

Background:

Currently cranioplasty treatment planning involves

several steps. It starts with three-dimensional tomographic imag-

ing of the trauma site followed by computer modelling of the

corresponding implant. Besides biological factors, fixation device

arrangement and osteotomy geometry influence the quality and

stability of the cranial implant assembly.

Objectives:

In this study 6 preoperative designs for

polymethylmethacrylate-based reconstructions of cranial

defects were evaluated for their mechanical robustness using

finite element analysis.