322
by computing the CT data of the structures. The mandibular rota-
tion was broken down into the frontal and the horizontal rotation.
Connection of the two rotational centres was the mandibular rota-
tion axis. The rotational centre was measured from the point where
the midface OSP met the lower chin border (FC) and the frontal
rotational centre distance (FRCD) and the horizontal rotational
centre distance (HRCD) were recorded.
Findings and Conclusion:
Analysis results showed that the rota-
tional axes highly varied in its location. The median FRCD was
126.1 mm (range,
−
195.9 to 2304.1 mm) and the median HRCD
was 153.4 mm (range,
−
110.3 to 2942.7 mm). There was no sig-
nificant difference between the FRCD and HRCD (
P
= 0.855).
Because of the highly variable location of the axes, the mandibular
rotations could hardly be categorised as roll, yaw or a combination
of them, which is defined as rotation around the geographic centre
of the structure. As a result, de-rotation of the mandible would be
difficult without using the OSPs as guides.
http://dx.doi.org/10.1016/j.ijom.2017.02.1084The application of digital technology for 12 patients in
dentomaxillofacial deformities
W.Y. Chuo
School of Stomatology, Hospital of Stomatology, China Medical
University, China
Objective:
To explore the application of digital technology in the
treatment of dentomaxillofacial deformities.
Methods:
Twelve patients of dentomaxillofacial deformities were
enrolled with three-dimensional (3D) computed tomography of
maxillary and mandible. The dicom date was input into the
software of Proplan CMF. We built a digital skull model and 3D-
printed skull model to perform surgical planning, postoperative
prediction and simulate operation. Clinical examination of facial
symmetry was performed 3 months later.
Results:
All the surgical planning, postoperative predictions and
simulate operations of the twelve patients of dentomaxillofacial
deformities were performed, and the orthognathic surgeries were
successful. The patients were satisfied with the facial symmetry 3
months after operations, with a satisfaction rate of 91.67%.
Conclusion:
Using digital technology to perform surgical plan-
ning and simulate surgery improved the accuracy of surgeries
and resulted in satisfied effect. Therefore, digital technology has
practical value in dentomaxillofacial deformities.
http://dx.doi.org/10.1016/j.ijom.2017.02.1085Non-grafted sagittal split osteotomy versus grafted sagittal
split osteotomy to reduce mandibular lower border defects in
orthognathic surgery. A cohort study
A. Contreras
∗
, J.O. Adbaje, D. Jerez, N. Yanine, A. Gantz,
A. Barrera, J. Cifuentes, C. Politis
Maxillofacial Surgery Unit, Faculty of Medicine, Clínica
Alemana de Santiago – Universidad del Desarrollo, Santiago,
Chile
Background:
The prevention of mandibular lower border defects
is an important issue to be taken into account after largemandibular
advancement with bilateral sagittal split osteotomy (BSSO).
Objectives:
The aim of this study is to compare the incidence of
mandibular border defects when non-grafted BSSO versus grafted
BSSO are used.
Methods:
The authors undertook a retrospective cohort study
comparing two different sagittal split osteotomies techniques:
Group A: traditional non-grafted BSSO technique and Group B:
traditional grafted BSSO technique. One year after surgery, the
presence or absence of a defect was determined by the use of
panoramic X-rays.
Results:
A total of 600 operation sites in 300 patients were
included in the study (age, sex and mandibular advancement were
similar between the groups
P
> 0.05). The proportion of lower
border mandibular defects of operation sites was: group A 36.5%
and group B 1.5%. Traditional grafted BSSO technique was sub-
stantially superior preventing the incidence of mandibular lower
border defects compared with traditional non-grafted BSSO tech-
nique (
P
< 0.05).
Conclusions:
Mandibular lower border defects are likely to hap-
pen after large mandibular advancement. The results in this study
show a considerably reduced occurrence of this type of defect
using grafted BSSO.
http://dx.doi.org/10.1016/j.ijom.2017.02.1086Evaluation of condylar positioning in bimaxillary
orthognathic surgery using intraoperative cone-beam
computed tomography
A. Contreras
∗
, J. Altschiller, A. Gantz, A. Barrera, N. Yanine,
R. Cosmelli, C. Gaete, J. Cifuentes
Faculty of Medicine, School of Dentistry Clínica Alemana –
Universidad del Desarrollo Clínica Alemana de Santiago,
Santiago, Chile
Background:
Bilateral sagittal split osteotomy (BSSO) consti-
tutes the most used surgical method in the treatment of dentofacial
deformities. Alterations in the condylar position, after the BSSO,
can lead to recurrence of postoperative malocclusions, tem-
poromandibular joint disorders (TMJ) and condylar resorption.
Nowadays, the use of intraoperative cone-beam would allow to
objectify the condylar position after the BSSO, avoiding deleteri-
ous effects on TMJ for wronged condylar positioning, optimising
masticatory efficiency, functionality and postoperative skeletal
stability.
Objectives:
Design a tomographic intraoperative control protocol,
with O-Arm cone-beam equipment, of condylar positioning in
BSSO on orthognathic surgery (OS) and evaluate its utility.
Methods:
Clinical prospective study made between July 2013
and August 2016 of 300 patients who underwent OS at the Oral
and Maxillofacial Unit, Faculty of Medicine, School of Dentistry
Clínica Alemana – Universidad del Desarrollo Clinica Alemana
Santiago, Chile. In operating room, after BSSO, with radiopro-
tection protocol, O-Arm cone-beam is used with multiplanar and
three-dimensional images. The condylar position is evaluated, and
if necessary, new repositioning and new control is made.
Conclusions:
The use of intraoperative cone-beam is a reliable
technique that allows performing an immediate diagnosis of wrong
condylar positioning in OS, avoiding future complications.
http://dx.doi.org/10.1016/j.ijom.2017.02.1087




